HannsG Computer Monitor JC199D User Manual

19 inch TFT LCD Monitor  
JC199D  
USER’S MANUAL  
 
Recycling Information  
We, the Hanns.G care very much about our environment protection strategy and firmly  
believe that it helps us have healthier earth via appropriate treatment and recycling of  
industrial technology devices at the end-of-life.  
These devices contain recyclable materials, which can be re-decomposed and re-integrated  
into brand-new marvels. On the contrary, other material can be classified to hazardous and  
poisoned substances. We strongly encourage you to contact the provided information to  
recycle this product.  
For more information, please visit  
 
Operation Instructions  
Thank you for purchasing this monitor, a high-resolution multi-scan color  
monitor.  
Please read this guide thoroughly before installation.  
FCC RADIO FREQUENCY INTERFERENCE STATEMENT  
WARNING: (FOR FCC CERTIFIED MODELS)  
This monitor has been tested and found compliant with the limits for a  
Class B digital device, pursuant to part 15 of the FCC Rules. These limits  
are designed to provide proper protection against harmful interference to a  
residential installation. This monitor generates, uses, and can radiate radio  
frequency energy. Harmful interference to radio communication may be led  
as a result if it‘s not properly installed and used. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
monitor does cause serious interference to radio or television reception,  
resetting the monitor may determine it. Moreover, users are encouraged to  
correct interference by doing one or more of the following:  
Reorient or relocate the receiving antenna.  
Move the monitor and the receiver further away from each other.  
Connect the monitor into an outlet on a circuit different from that to  
which the receiver is connected.  
Consult your local dealer or an qualified technician.  
FCC Warning:  
To assure a continued FCC compliance, a user must use a grounded  
power supply cord and the provided shielded video interface cable with  
bonded ferrite cores. Also, any unauthorized changes or modifications to  
this monitor would void the user‘s authority to operate this device.  
Note: If necessary, shielded interface cables and AC power cord must be  
used to meet the emission level limits.  
 
Content  
Safety Precautions.............................................................................1  
Quick Installation................................................................................2  
Front View of the Product ..................................................................3  
Supporting Timing Modes..................................................................7  
Technical Information.........................................................................8  
 
Safety Precautions  
This monitor is manufactured and tested on a ground principle that a user’s  
safety comes first. However, improper use or installation may result danger  
to the monitor as well as to the user. Carefully go over the following  
WARNINGS before installation and keep this guide handy.  
WARNINGS:  
This monitor should be operated only at the correct power sources  
indicated on the label on the rear end of the monitor. If you’re unsure of  
the power supply in your residence, consult your local dealer or power  
company.  
Do not try to repair the monitor yourself as it contains no  
user-serviceable parts. The monitor should only be repaired by a  
qualified technician.  
Do not remove the monitor cabinet. There is high-voltage parts inside  
that may cause electric shock to human bodies, even when the power  
cord is disconnected .  
Stop using the monitor if the cabinet is damaged. Have it checked by a  
service technician.  
Put your monitor only in a clean, dry environment. Unplug the monitor  
immediately if gets wet and consult your service technician.  
Always unplug the monitor before cleaning it. Clean the cabinet with a  
clean, dry cloth. Apply non-ammonia based cleaner onto the cloth, not  
directly onto the glass screen.  
Keep the monitor away from magnetic objects, motors, TV sets, and  
transformer.  
Do not place heavy objects on the cable or power cord.  
For PLUG CABLE EQUIPMENT, the Socket-outlet shall be installed  
near the equipment and shall be easily accessible.  
LAMP DISPOSAL  
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR  
DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE  
INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.  
FOR LAMP SPECIFIC DISPOSAL INFORMATION CHECK WWW.LAMPRECYCLE.ORG.  
1
 
 
First Setup  
Congratulation for purchasing this monitor of high performance!  
This monitor comes with the following accessories :  
Power cable.  
D-Sub cable (15 pin)  
DVI cable (24 pin)(Optional)  
Audio cable.  
User guide.  
Quick Installation  
1. Connect video cable (D-Sub cable)  
Make sure both monitor and computer are powered OFF. Connect the video  
cable (D-Sub cable) to the computer, then to the monitor.  
2. Connect DVI cable  
Connect the DVI cable from DVI output of computer to the DVI input of the  
monitor.  
3. Connect power cord  
Connect the power cord to a properly grounded AC outlet, then to the monitor.  
4. Power-ON computer and monitor  
Power-ON the computer, then Power-ON the monitor.  
5. Windows users: Setting the Timing Mode (Resolution and Refresh Rate)  
Example: 1280 x 1024 @ 60 Hz  
Resolution Right-click on the Windows desktop > Properties > Settings >  
“Desktop Area”. Set the resolution.  
Refresh Rate (vertical frequency) See your graphic card’s user guide for  
instructions.  
Example:  
Power cable  
D-Sub cable  
2
 
 
Front View of the Product  
➋➌  
➍ ➎  
OSD TURN ON/OFF  
SCROLL DOWN/DECREASE  
SCROLL UP/INCREASE  
CONFIRM SELECTION  
POWER ON/OFF  
LED INDICATOR  
Rear View of the Product  
POWER INPUT  
AUDIO INPUT  
DVI INPUT (DVI 24 PIN)  
VGA INPUT (D-SUB 15 PIN)  
3
 
 
Using On Screen Display (OSD) Functions  
1
Display main menu.  
Exit from OSD menu.  
2
Auto adjust the image when not in main menu.  
Confirm the selection.  
V or W  
Select the desired item when in OSD menu.  
When not in OSD menu, it is to immediately activate Contrast/  
Brightness. It should be change to Contrast/ Brightness by pressing  
button 2.  
+ Recall both of Contrast and Brightness.  
1 +  
1 +  
Power Lock (when not in OSD menu)  
OSD Lock (when not in OSD menu)  
Main Menu  
4
 
 
Short Cuts Function from the button(s)  
Auto Adjust : To auto adjust Horizontal Position, Vertical Position, Phase  
(Fine Tune) and Clock (H. Size) of the screen.  
Contrast : To adjust the foreground white level of screen image.  
V : increase contrast, W: decrease contrast.  
Brightness : To adjust the luminance of the video.  
V : increase brightness, W : decrease brightness.  
Color Adjust : To select the color for improving brightness and color  
saturation between cool, normal, warm, and User Color.  
Cool : Adds blue to screen image for cooler white.  
Normal : Adds red to screen image for warmer white and richer red.  
Warm : Adds green to screen image for a darker color.  
User Color : Individual adjustments for red (R), green (G), blue (B).  
1. Press button 2 to select the desired color.  
2. Press W or V button to adjust selected color.  
Information : To display the information, regarding the current input signal  
coming from the graphic card in your computer.  
Note: See your graphic card user guide for more information about  
changing the resolution and refresh rate.  
Image Adjust : To manually adjust the Horizontal/ Vertical position, H. Size,  
Fine Tune and Sharpness.  
H./V. Position : To adjust the horizontal and vertical position of the video.  
H. Position : V : move screen to the right, W : move screen to the left.  
V. Position : V : move screen up, W : move screen down.  
H. Size : To adjust the width of the screen image.  
W : decrease the width of screen image, V : increase the width of screen  
image.  
Fine Tune : To adjust the delay time of data and clock.  
Press W or V to adjust to your preference.  
5
 
 
Sharpness : To adjust the clarity of a non-SXGA (1280x1024) signal with  
W or V button.  
Setup Menu : To set up Language Select, Resolution Notice, OSD Position,  
OSD Time Out, and Input Select (Analog).  
Language Select : To allow users to choose from available languages.  
Resolution Notice : Resolution Notice is to remind you set the best quality  
for the image.  
Choose “Enable” : Every 30 seconds, it will show a window “ For best  
picture quality change resolution to 1280 x 1024” to remind you set the  
best quality for the image.  
Choose “Disable” : It will not show a window to remind you set the best  
quality for the image if the resolution is lower than 1280 x 1024.  
OSD Position : Press 2 button to select between horizontal and vertical  
OSD Position adjustment.  
Horizontal OSD Position : To horizontally adjust the OSD position.  
V : move OSD to the right, W : move OSD to the left.  
Vertical OSD Position : To vertically adjust the OSD position.  
V : move OSD up, W : move OSD down.  
OSD Time Out : To automatically turn off On Screen Display(OSD)after a  
preset period of time.  
Input Select : When press Input Select change Input signal to Analog or  
Digital.  
Memory Recall : To recall factory settings for Video & Audio controls.  
Press button 2 to select the Memory Recall menu option.  
Audio Menu : To adjust the audio functions.  
Volume : To adjust the volume of speaker output.  
Mute : To turn the Mute ON/OFF.  
6
 
 
Supporting Timing Modes  
VGA  
720 x 400 @ 70Hz  
VGA  
640 x 480 @ 60Hz  
640 x 480 @ 67Hz  
640 x 480 @ 75Hz  
800 x 600 @ 56Hz  
800 x 600 @ 60Hz  
800 x 600 @ 72Hz  
800 x 600 @ 75Hz  
832 x 624 @ 75Hz  
1024 x 768 @ 60Hz  
1024 x 768 @ 70Hz  
1024 x 768 @ 75Hz  
1280 x 1024 @ 60Hz  
1280 x 1024 @ 75Hz  
MAC  
VESA  
VESA  
VESA  
VESA  
VESA  
MAC  
VESA  
VESA  
VESA  
VESA  
VESA  
Warning : Do not set the graphic card in your computer to exceed these maximum  
refresh rates. Doing so may result in permanent damage to your monitor.  
7
 
 
Technical Information  
Technical Specification  
LCD Panel  
19.0” TFT  
Power Management  
Energy Star compliant VESA  
DPMS compatible  
< 2 W  
Displayable Resolution SXGA 1280 x 1024 max. Vertical Frequency 75Hz max.  
Pixel Dimension  
LCD Display Color  
Tilt  
0.294 x 0.294 mm  
16.2M (6 bits + FRC/ color)  
0°~20°  
Active Display Area  
Temperature  
376 mm x 301mm  
Operating: 0°C ~ +40°C  
Storage: -20°C ~ + 60°C  
Compliance  
Power  
UL, TUV/GS, CE, FCC-B, Energy Star,TUV/Ergo, TCO03  
Input Voltage AC100-240 V  
1W x 2  
Speaker  
8
 
 
Care and Maintenance  
Care  
Avoid exposing your monitor directly to sunlight or other heat source. Place your  
monitor away from the sun to reduce glare.  
Put your monitor in a well ventilated area.  
Do not place any heavy things on top of your monitor.  
Make certain your monitor is installed in a clean and moisture-free area.  
Keep your monitor away from magnets, motors, transformers, speakers, and TV  
sets.  
Note  
Move the LCD out of the package and take off the plastic bag and Polystyrene Foam.  
Pull the base from Parallel versus Panel to Vertical.  
Adjust the Panel within 0 degree leaning forward and 20 degree leaning  
backward. You must bend harder to exceed 20 degree backward but this range  
is for packing the unit to a small size for storage only.  
Safety Tips  
If smoke, abnormal noise or odor came out from your monitor, caution you  
should remove the power cord immediately and call your service center.  
Never remove the rear cover of your monitor cabinet. The display unit inside  
contains high-voltage parts and may cause electric shock to human bodies.  
Never try to repair your monitor yourself. Always call your service center or a  
qualified technician to fix it.  
Troubleshooting  
No power  
Make sure A/C power cord is securely connected to the power adapter and the  
power supply is firmly connected to the monitor.  
Plug another electrical device into the power outlet to verify that the outlet is  
supplying proper voltage.  
Make sure all signal cables are installed.  
Power on but no screen image  
Make sure the video cable supplied with the monitor is tightly secured to the  
video output port on back of the computer. If not, tightly secure it.  
Adjust brightness.  
9
 
 
Wrong or abnormal colors  
If any colors (red, green, blue) are missing, check the video cable to make sure  
it is securely connected. Loose or broken pins in the cable connector could  
cause an improper connection.  
Connect the monitor to another computer.  
According to WEEE regulation , this monitor can't be handled as  
normal trash in Europe when it is out of usage. Please refer to the  
recycle information from our website to handle it.  
10  
 

Graco Baby Accessories PD203261B User Manual
Heat Glo LifeStyle Indoor Fireplace FB GRAND S User Manual
Hotpoint Dishwasher HDA6009 User Manual
HP Hewlett Packard All in One Printer PSC 2210 User Manual
HP Hewlett Packard Photo Printer 7830 User Manual
Humax Flat Panel Television LDE 32DST User Manual
Hunter Fan Air Cleaner 30836 User Manual
Hypertec Mouse HKB260CWHLC User Manual
Hyundai Car Satellite TV System H CDM8010 User Manual
Impex Home Gym MP PWR100 User Manual