Haier TV Receiver WL19T1 User Manual

LCD TV RECEIVER  
USER'S MANUAL  
MODEL:  
WL19T1, WL22T1  
Please read this manual carefully before  
using your television and keep this manual  
In a good place for future reference.  
 
Safety Notice Items  
Incorrect usage will cause fire or electric shock. To prevent this, please do  
as required when you are installing, using and cleaning this machine. To insure  
your safety and extend the life-span of LCD-TV, please read the following items  
carefully before using:  
Please read andunderstand all theinstructions before operation;  
Please keep the book for later use;  
Please comply with the warning instructions on the machine and in this book  
strictly;  
Please comply with the instructions provided;  
Please do not use additional devices that are not recommended by  
manufacturer:  
Before operation, please make sure that the operating voltage of your unit is  
normal;  
Do not placethe unit onunstable, dusty andhumid places;  
Never put theunit in directsunlight or nearheat sources;  
Allow enough space for proper ventilation;  
Please keep water away from the LCD-TV . If water comes in contact with the  
LCD-TV, disconnect the power cord from the power source, then wipe the set  
with a dry soft cloth;  
Do not remove the back cover. If services were need, please refer to qualified  
Personnel  
 
Front Panel Controls  
T1  
Control Panel Function  
1. Power supply switch  
2.TV/AV  
Select the input signals: TV/AV/S-VIDEO/PC/COMPONENT  
3. MENU Press to select the main menu  
4. VOL- Volume down / Left orientation to adjust the item in the OSD  
VOL+ Volume up / Right orientation to adjust the item/Press to enter  
5. CH- TV channel down / to select the item in the menu  
CH+ TV channel up / to select the item in the menu  
6. Power indicator  
Illuminates red in standby mode, illuminates green when the display is  
turned on  
7.Remote Sensor  
Receiving remote control sends the infrared remote  
signal.  
 
Connection Options  
The figure is just for reference, please see the real.)  
AV /S-VIDEO/COMPONENT Audio Input  
Connect audio  
output from an external  
device to this jack  
COMPONENTInput  
Connect a componentvideo/audio  
device to thesejacks  
Earphone port  
Pb  
Pr  
Y
R
L
V
VGA IN  
ANT IN  
PC AUDIO IN  
VIDEO IN  
S-VIDEO  
COMPONENT IN  
AUDIO IN  
PC Audio Input  
S-Video Input  
Connect S-Video out  
from an S-Video device  
to the jacks.  
Connect the PC output  
connector from a PC to  
the audio input port  
VGA Input  
Video Input  
Connect video  
output from an external  
device to this jack  
Connect to the VGA  
15PIN analog output  
connector of the PC  
display card for PC  
display purpose  
Antenna Input  
 
Remote Control Key Functions  
When using the remote control, aim it  
Buttons on the remote control  
towards the remotesensor on theTV  
Stand By  
MUTE  
Display current input signal information  
TV channel number select  
Set time to change the TV into the  
standby status after a period of preset  
time.  
SLEEP DISPLAY MUTE POWER  
NICAM  
PC  
AUTO AD TV/AV  
NICAM/A2 Stereo select  
EXIT  
Quick TV channel switch(return to the  
last channel)  
Volume down/up Left/right orientation to  
adjust the item in the OSD  
TV channel up/down or select the item  
of the menu  
PSM  
OK  
SSM  
Select TV/AV/S-VIDEO/PC/  
COMPONENT  
Q.VIEW  
Select picture mode  
P+  
PC system select  
Select sound mode  
Correspond to the differently colored  
subjects  
V-  
V+  
MENU  
Switch to the Teletext with text mode/turn  
off Teletext and switch to TV mode  
Hold on or off for current page display  
Switch to the Teletext with mix mode  
Request index page  
P-  
INDEX  
TEXT  
SUBCODE MIX  
Change display size  
Sub coded page access  
While in normal TV mode only, pressing  
the button TIME will display the teletext  
time in the top right corner for a few  
seconds.(only available in teletext mode)  
Reveal or hidden the hidden words  
Press to select the main menu  
Auto adjust (PC mode)  
TIME  
HOLD  
SIZE  
REVEAL  
 
Remote Control  
Installing Batteries  
1.Slide open the cover of the battery compartment on the back of the remote  
control.  
2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to  
respective mark)  
3.Replace the cover of the battery compartment.  
1
2
3
Precautions  
As strong light may interfere the  
signals, change yourposition to  
operate the remote controller if  
the television cannot be turned  
on or off as youexpect.  
Make sure that there is no  
obstacle between theremote  
controller and televisionset.  
Make sure that two 5# 1.5V alkaline  
batteries are loaded. The batteries  
must be of the same type. The batteries  
must be located properly. The batteries  
are not rechargeable.  
Keep the remote controller  
away from heat source or  
humid area toensure  
effective performance of  
the remote controller.  
 
Connection Instructions  
Grounding  
Ensure that you connect the grounding / earth wire to prevent possible  
electric shock. If grounding methods are not possible, have a qualified  
electrician install a separate circuit breaker. Do not try to ground the  
unit by connectingit to telephone wires, lighteningrods, or gaspipes.  
External Equipment Connections  
Antenna Connection  
- Antenna or Cable Service with a Cable Box Connections  
- For optimum picture quality, adjust antenna direction if needed.  
Multi-family Dwellings/Apartments  
(Connect to wall antenna socket)  
wall antenna  
socket  
ANT IN  
RF coaxial wire (75 ohm)  
VHF antenna  
UHF antenna  
Be careful not to bend the bronze  
wire when connecting the antenna.  
outdoor  
antenna  
Single-family Dwellings /Houses  
(Connect to wall jack for outdoor antenna)  
To improve picture quality in a poor  
signal area, purchase and install a  
signal amplifier.  
ANT IN  
If the antenna needs to be split for two  
TV s, install a 2-Way Signal Splitter  
in the connections.  
If the antenna is not installed properly,  
contact your dealer for assistance.  
Note:All cables shownare just forexample.  
 
Connection Instructions  
VGA Input  
You can use your LCD-TV as a monitor for your personal computer using a VGA  
cable (not supplied).  
Connection and use steps:  
1.Read the userguide supplied with  
your computer and ensure that it has  
a VGAconnector;  
2.Make sure that the power of the LCD  
-TV and thePC are off;  
VGA IN  
3.Connect a Dtype 15-pin VGAinterface  
cable ( not supplied ) to the VGAvideo  
interface connector on the PC. Then  
connect the other end to the PC video  
interface connector on the back of the  
LCD-TV.Tighten the screwson the VGA  
connectors once they are firmly  
connected;  
4.Turn on the power ofthe LCD-TV first ,  
and then turn on the power of the PC;  
5.Press the TV/AV button to set the video  
input mode of the LCD-TV to PC;  
6.Check the imageon your TV. There may be noise associatedwith the resolution,  
vertical pattern, contrast or brightness in PCmode. If noise is present, change  
the PC modeto another resolution, change the refreshrate to anotherrate or  
adjust the brightnessand contrast onthe menu untilthe picture isclear. Ifthe  
refresh rate of the PC graphic card can not be changed, change the PC graphic  
card or consult the manufacturer of the PC graphic card.  
Resolution  
Mode  
VGA  
Resolution  
640*480  
Line frequency (Khz) Frame frequency (Hz)  
31.5KHz  
37.9KHz  
48.4KHz  
60Hz  
60Hz  
60Hz  
SVGA  
XGA  
800*600  
1024*768  
Note: Allabove listed aresubject to VESACriteria.  
YPbPr Input  
How to connect  
Connect the DVD video outputs (Y, PB, PR)  
to the COMPONENT(Y, Pb, Pr) IN jacks on  
the TV and connect theDVD audio outputs  
to the AUDIO IN jacks on the TV, as shown  
in the figure.  
NOTE: If your DVD player doesnot have  
component video output,use S-Video.  
How to use  
1. Turn on the DVD player, insert a DVD.  
2. Use the TV/AV button on theremote control toselect  
 
Connection Instructions  
COMPONENT (If connected to SVIDEO,select the SV external  
input source.)  
3. Refer to the DVD player's manual for operating instructions.  
Component Input ports  
To get better picture quality, connect a DVD player to the component  
input ports as shown below.  
Y
Pb  
Pr  
S-VIDEO Input  
- To avoid picture noise (interference), leave an adequate distance between the  
VCR and TV  
Connection and use steps:  
1.Read the user guide supplied with your AV devices and ensure that it has  
S-Video connectors;  
2.Make sure that the power of the LCD-TV and the AV device are off;  
Connection Option 1  
Set VCR output switch to 3 or 4 and then  
tune TV to the same channel number.  
Connection Option 2  
1. Connect the audio and Svideo cables  
from the VCR's output jacks to the TV  
input jacks, as shown in the figure.  
2. Insert a video tape into the VCR and  
press PLAY on the VCR. (Refer to the  
VCR owner s manual.)  
2
3.Turn on the power of the LCD-TV first ;  
and then turn on the power of the AV  
device;  
1
4.Press the TV/AV button to set the video  
input mode of the LCD-TV to S-VIDEO  
mode .  
VCR  
 
Connection Instructions  
Cable TV Input  
- After subscribing to a cable TV service from a local provider you can watch cable  
TV programming. The TV cannot display TV programming unless a TV tuner  
device or cableTV converter box is connectedto the TV.  
- For furtherinformation regarding cableTV service, contact your localcable TV  
service provider(s).  
Connection Option 1  
1. Select 3 or 4 with channel switch on cable  
box.  
2. Tune the TV channel to the same selected  
output channel oncable box.  
3. Select channelsat the cablebox or with  
the cable box remote control.  
Connection Option 2  
1. Connect the audio and video cables from  
the Cable Box'soutput jacks tothe TV  
input jacks, as shown in the figure.When  
connecting the TV to a Cable Box, match  
the jack colors  
(Video = yellow, Audio Left = white, and  
Audio Right= red).  
2. Select the input source by using the TV/AV  
button on the remote control.  
3. Select your desired channel with the  
remote control forcable box.  
External AV Source Input  
How to connect  
Connect the audio and video cables from  
the external equipment's output jacks to the  
TV input jacks, as shown in the figure.  
When connecting the TV to external equip-  
ment, match the jack colors (Video = yellow,  
Audio Left =white, andAudio Right =red).  
How to use  
1. Select the input source by using the TV/AV  
button on the remote control.  
2. Operate the corresponding external equi-  
pment. Refer to external equipment ope-  
rating guide.  
 
Basic Operating Instructions  
Turn on the LCD-TV  
SLEEP DISPLAY MUTE POWER  
When the POWER button on the remote control is pressed  
and the LCD-TV is turned on, the indicator light on the front of  
the LCD-TV changesfrom red togreen. When theLCD-TV is  
turned off using the POWERbutton, the LCD-TVwillgo into  
standby mode and the indicator light turns red.  
NICAM  
PC  
AUTO AD TV/AV  
PSM  
OK  
.SSM  
Q.VIEW  
Note:  
The display of the input mode will disappear in about 8  
seconds.  
P+  
V-  
MENU  
V+  
P-  
INDEX  
TEXT  
SUBCODE MIX  
You can also turn on the TV from standby mode by pressing  
the digits(1-9) orP+/- .  
TIME  
HOLD  
SIZE  
REVEAL  
Switch AmongDifferent Inputs: TV/AV/S-VIDEO/PC/COMPONENT  
Each time you press the TV/AV button, TV/AV/S-VIDEO/PC/COMPONENT will  
appear on the screen .  
The display will appear on the screen when the TV is turned on the first time:  
(Different displays for different countries, please see the real set)  
AUTO SEARCH  
AUTO SEARCH  
or  
UNITED KINGDOM  
NO  
OTHER  
YES  
NO  
YES  
Press V+/- to adjust among countries list on the screen just according to the  
country you are in, P+/- to select the option and MENU to confirm.  
Audio Control  
1.Press the V+ button to increase the volume. A number will appear on  
screen indicating the volume level.  
2.Press the V- button to decrease the volume. A number will appear on  
screen indicating the volume level.  
Mute  
1.Press the MUTE button to mute the sound temporarily. A mute icon  
appears on the screen.  
2.Press the MUTE button again or V+/V- to restore the sound.  
The mute icon disappears.  
 
Basic Operating Instructions  
Select the TV Channel You Want  
You can use the number keys on the remote control to directly select TV  
channels.  
The LCD-TV can store up to 100 channels , and you can press the keys on the  
remote control or on the panel to make a selection.  
1.Press the relevant key on the remote control if you want to choose any channel  
from 0 to 9. for example: if you want to choose channel 8, just press the key  
number 0 and 8.  
Note: You must press 0 first and then the other numbers from 0 to 9 if you want  
To choose channels from 0 to 9)  
2.If you want to choose a channel bigger than 9, please enter the two digits of the  
channel number you want to watch within 3 seconds. for example: select  
channel 16  
Picture Mode  
Press PSM button on the remote control for menu display . For desired mode as  
follows:  
PERSONAL STANDARD MILD FRESH  
 
Menu Operations  
* In this manual, the OSD (On Screen Display) may be different from your TV  
because it is just an example to help you with the TV operation.  
s
Press TV/AV to select the input source, and the menu in the different source is  
different .  
1. Press MENU button to display the main menu, and V+/V-to select the  
main menu .  
2. Press P+/P- to scroll through the options  
3. Press V+/V- buttons to make changes to the parameters  
4. Press the OK button to exit the menu  
Picture Menu Options  
Picture quality can be adjusted for any input separately .  
The picture qualityon the screencan be adjustedas follows:  
1. Press MENU button and V+/V- until the followingmenu appears  
on the screen.  
2. Press P+/P- button to enterthe picture menuand to goup and downto  
select the desired option .  
PC MENU  
COMPONENT MENU  
PICTURE  
PICTURE  
BRIGHTNESS  
CONTRAST  
SHARPNESS  
COLOUR TEMP.  
30  
30  
2
BRIGHTNESS  
CONTRAST  
SHARPNESS  
COLOUR  
30  
30  
2
COLD  
30  
0
0
H.POSITION  
V.POSITION  
30  
30  
TV/AV/S-VIDEO MENU  
PICTURE  
BRIGHTNESS  
CONTRAST  
SHARPNESS  
COLOUR  
50  
50  
2
50  
OFF  
50  
NOISE REDUCTION  
HUE  
Only available inNTSC system  
Note: Sign ontop of themenu in thismanual may bedifferent from the real  
 
Menu Operations  
Picture Menu Options continued  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference .  
4. Repeat step 2 and step 3 until desired picture quality has been achieved .  
Function:  
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it  
will add more light to dark parts of the picture and by decreasing the level ,it will  
add more dark to light parts of the picture.  
CONTRAST : Adjust the contrast of the picture . The image becomes higher as  
the number increase.  
SHARPNESS : Adjust the amount of the detail enhancement , the image  
sharpness rises as the number increases (By increasing the level, it will show  
cleaner and clearer images and by decreasing the level, it will make picture  
smoother).  
COLOUR : Press V+/V- to adjust the colour  
NOISE REDUCTION: Adjust the quality of the picture by selecting OFF,LOW,  
MID,HIGH.  
HUE : Adjust the tone of the picture . Appear and be adjusted only under NTSC  
mode  
COLOUR TEMP. : Press to select the colour temperature from WARM/NORMAL/  
COLD .  
H.POSITION : Picture horizontal adjust  
V.POSITION : Picture vertical position adjust .  
Audio Menu Options  
Sound can be adjusted for any input as follows:  
1. Press MENU and V+/V- button until the following menu appears on  
the screen  
AUDIO  
50  
50  
50  
50  
VOLUME  
BALANCE  
BASS  
TREBLE  
AUDIO MODE  
AVL  
VOICE  
OFF  
 
Menu Operations  
Audio Menu Options continued  
You can adjust sound options to the levels you prefer.  
2. Press P+/P- button to enterthe audio menuand to goup and downto  
select the desired option .  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option toyour preference .  
4. Repeat step2 and step3 until desiredsound quality hasbeen achieved ..  
Function :  
VOLUME :Adjust the volumeof your TV  
BALANCE : Adjust the balanceof the audiooutput from leftto right . When  
indication value of balance increases toward 100 , sound of the left speaker  
becomes weaker . When indication value of balance decreases toward 0,  
sound of the right speaker become weaker .  
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .  
TREBLE : Adjust thetreble of thesound . Canonly be adjustunder PERSONAL  
mode .  
AUDIO MODE : Press V+/V- to select among PERSONAL, VOICE, MUSIC and  
THEATRE .  
AVL: Automatic Volume Limit Control reduces the effect of the large volume by  
the same volume of all the channels .  
 
Menu Operations  
Function Menu Options  
1. Press MENU button and V+/V- until the following menu appears  
on the screen.  
FUNCTION  
INPUT SOURCE  
LANGUAGE  
TV  
ENGLISH  
PAN EUROPEAN  
EAST  
TXT LANGUAGE  
TXT EAST/WEST  
BLUE SCREEN  
DISPLAY MODE  
RESET  
ON  
4:3  
CHILD LOCK  
2. Press P+/P- button to enterthe function menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference .  
4. Repeat step 2 and step 3 until desired picture quality has been achieved .  
Functions:  
1. INPUT SOURCE : Display current mode . There are TV/AV/S-VIDEO/PC/  
COMPONENT to display .  
2. LANGUAGE: This item displays the language of the OSD.  
3. TXT LANGUAGE: To switch the teletext languages.  
4. TXT EAST/WEST: To select EASTor WEST.  
5.DISPLAY MODE: To select the display mode :4:3/16:9/FULLSCREEN.  
6.BLUE SCREEN :To set On, the screen will be in blue screen after 3 seconds  
if there is no signal.  
7. RESET : Press V+ to reset somesettings to thefactory default .  
8. CHILD LOCK:Press V+ to enter it and input the password correctly, the  
CHILD LOCK menu will appear on the screen.  
PASSWORD: The password can be changed. Press P+/- to select PASSWORD  
and V+ to enter. The screen will display NEW PW:----,then enter the new  
password and the screen display CONFIRM PW:----, if the same password is  
input correctly twice, the old password will be changed.  
CHILD LOCK: Press P+/- to select it . Press V+/- to set on or off mode. If lock  
on mode is set, child lock is inactivated automatically. In such case, buttons  
on the television is useless and only buttons on remote control can be used,  
 
Menu Operations  
if buttons onthe television arepressed, the screenwill display CHILDLOCK.  
The child lockmode can beresumed by enteringlock set menu, set child lock  
on.  
Adjust Menu Options  
1. Press MENU and V+/V- button until the following menu appears on the  
screen  
ADJUST  
AUTO SYNC.  
PHASE  
CLOCK  
H. POSITION  
V. POSITION  
50  
50  
50  
50  
Note: This menu only appears in PC mode .  
2. Press P+/P- button to enter the adjust menu and to go up and down to  
select the desired option  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference ..  
4. Repeat step 2 and step 3 until desired quality has been achieved .  
Functions:  
AUTO SYNC : Is opted for adjustment of picture location frequency and phase  
parameters .  
PHASE : Removes any horizontal distortion and clears or sharpness the displayed  
characters .  
CLOCK : Adjust theTFT-LCD to match the PC inputsource  
H.POSITION : Picture horizontal adjust  
V.POSITION : Picture vertical position adjust.  
 
Menu Operations  
Tuning Menu Options  
1. Press MENU and V+/V- button until the following menu appears on the  
screen  
TUNING  
TUNING PROGRAM  
AUTO SEARCH  
Note: This menuonly appears inTV mode .  
2. Press P+/P- button to enterthe tuning menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference .  
4. Repeat step 2 and step 3 until desired quality has been achieved ..  
Functions:  
1.TUNING PROGRAM: Press V+ to enter it and the TUNING PROGRAM menu  
appears:  
TUNING PROGRAM  
CHANNEL  
1
EDIT NAME  
COLOUR SYSTEM  
SOUND SYSTEM  
SKIP  
AUTO  
DK  
OFF  
ON  
AFC  
FINE TUNE  
EXCHANGE  
MANUAL SEARCH  
143.65MHZ  
CHANNEL : Press V+/V- to change the TV channel .  
EDIT NAME: Press V+ to enter it , then press V+/- to select the position you want to  
edit and press P+/- to input the emblem such as character and so on.(There are 8  
position for you to edit totally)  
COLOUR SYSTEM : Select the TV color system from AUTO, PAL, SECAM.  
SOUND SYSTEM : Select the TV standard system from DK,I,L/L',BG .  
(L' may be not available in some countries)  
 
Menu Operations  
Tuning Menu Options Continued  
SKIP : If you want skip a channel , pressV+/V- to select ON , and this  
channel will be skip next time when you press P+/P- . But you can press  
digits button to select the channel . If you want to restore the channel , select OFF.  
AFC : Auto frequence control . Select ONto improve the image quality .  
FINE TUNE :Press P+/P- to select FINE TUNE item in menu . Then , press V+/V-  
button to adjust and improve the image quality .  
EXCHANGE : Press V+ to display the menu as follows:  
EXCHANGE  
FROM :  
TO :  
1
9
EXCHANGE  
Press P+/- to select the item and then V+/- to adjust the channel and V+  
to confirm.( For example: pressP+/- to select FROM item, and then press  
V+/- to adjust the channel number to 1; then Press P+/- to select TO item,  
and V+/- to adjust the channel number to 9; press P+/- to select EXCHANGE item,  
and then V+ to confirm. The two channels will be exchanged)  
MANUAL SEARCH : Press V+ to start to search the channel . The following menu  
will display on the screen:  
MANUAL SEARCH  
DOWN  
UP  
Press V+/- to select UP or DOWN, and then press MENU to confirm.  
(If you select DOWN, the search will search the lower frequency channel and UP  
will search the higher frequency channel)  
2. AUTO SEARCH : Auto search and save the channel .Press the V+ button to  
start to search the channel and the following menu will appears on the screen:  
AUTO SEARCH  
NO  
YES  
Press V+/- to select YES or NO, and menu to confirm.  
You could press MENU to stop the search.  
NOTE: If you want to search the channels in L or L' system, you need to set the sound  
system to L in OSD  
 
TELETEXT  
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD  
control functions are not available in TELETEXT mode. If the TV is switched on by POWER  
after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will  
disappear automatically.  
Teletext features may vary depending on the Broadcasting  
Companies and is only available if the channel selected is  
SLEEP DISPLAY MUTE POWER  
NICAM  
PC  
AUTO AD TV/AV  
transmitting Teletext. Pressing the TEXT button whilst in  
Teletext operation will switch the current status to TV.  
When in Teletext mode, the volume may still be altered to  
the desired listening level.  
PSM  
OK  
.SSM  
Q.VIEW  
P+  
V-  
MENU  
V+  
Page Selection  
P-  
INDEX  
TEXT  
Pages can beselected in twoways:  
a. Press P+ or P- button to increase or decrease the  
page number by one.  
SUBCODE MIX  
TIME  
HOLD  
SIZE  
REVEAL  
b. By entering the page number, using the number  
keys on the remote control.  
SIZE Button  
Press SIZE button to change display size : normal large top large bottom  
normal  
REVEAL Button  
Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again  
to hide.  
Red/Green/ Yellow/CyanButtons  
These four buttons correspond to the differently colored subjects .  
HOLD Button  
Press HOLD button to remain the Teletext page when viewing multi-page  
information .  
INDEX Button  
Press INDEX button to return to the main index page .  
Depending on the way information is transmitted , this may have to be pressed  
more than once to return to the main index page .  
 
TELETEXT  
SUBCODE Button  
When Teletext information exceeds more than one page , it may take some time  
for the automatic changing of the sub pages to reach the sub page you require .  
It is possible to enter your required sub page and continue watching the normal  
programme until the correct sub page is found .  
Select the required page number using buttons 0-9 .  
If the top of the page indicates that sub pages are being transmitted yet the page  
does not change . Then the number at the top of the page is there to indicated  
that the broadcaster has updated the page s contents , there are no sub pages .  
Press SUBCODE button , page number/--- will be displayed at the bottom right  
of the screen.  
Enter desired sub page number before the page number/--- disappears . To  
select page 6 enter 0,0,0 and 6 .  
TEXT Button  
Press TEXT to enter Teletext mode and only the text page can be visible .  
MIX Button  
Press MIX button to enter Teletext mode and both the TV picture and text page  
can be visible.  
TIME  
While in normal TV mode only, pressing the button TIME will display the  
teletext time in the top right corner for a few seconds.  
Note: The teletext buttons could be working even if there is no teletext signal, but there  
is no teletext display.  
 
Troubleshooting Guide  
To assist in location possible faults use help guide below.  
Troubleshooting  
Verify ifthe television isproperly plugged.  
Verify ifthe television isproperly supplied power.  
Verify ifelectricity is available.  
No picture, no sound  
Verify if correct signals are input.  
Press TV/AV button to change signal input to TV input.  
Restart the television of power supply is interrupted.  
Blank screen  
Press MUTE button and verify if Mute mode is set.  
Switch to other channel and verify if the same problem  
happens.  
No sound  
Press VOL+ button to see if the problem can be solved.  
Verify ifsound system iscorrect. Refer tosome chapter  
for adjust.  
Poor sound  
Verify if correct channel is selected.  
Adjust the antenna.  
Make adjustments by FINE TUNE and MANUAL SEARCH.  
No picture in some  
channel  
Verify if the same problem exists in other channels.  
Check out of picture and sound systems.  
Refer to relative instructions in the Manual for color  
adjust.  
No color for some channel  
program (black and white)  
Verify ifthe antenna iscorrectly connected.  
Verify ifthe antenna isin good condition.  
Make fine adjustmentof channel.  
Spots with some or  
all pictures  
Disconnect the televisionfrom power supplyand, 10  
seconds later, connect the televisionto the powersupply.  
If the problemstill exists, contactauthorized after-sales  
service for technicalassistance.  
Television out of control  
Note:  
1.If the fault can not be repaired using the above guide consult with your local authorized service  
center.  
2.The TV set must only be repaired by a qualified registered service person. Never attempt to  
remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.  
 
Specifications  
Specifications of the television that you have just purchased may  
vary from the information in this table due to technical innovations.  
WL19T1  
WL22T1  
Model  
Picture, sound  
system  
PAL/SECAM-B/G,I,D/K,L,L  
1.5W+1.5W  
Audio output  
COMPONENT input PC input S-VIDEO input Audio input  
Video input Antenna input  
External input port  
~150-240V 50Hz  
Power requirements  
Power consumption  
Temperature  
60W  
70W  
Working:5 C~35 C  
Storage:-15 C~45 C  
Working:20%~80%  
Storage: 5%~90%  
Humidity  
Remote control  
Batteries  
Accessories  
Owner's manual  
Warranty card  
Note: Warranty card is only for the special countries and areas.  
Note:  
All specifications are subject to change without notice.  
All quality are approximate value.  
 
 
 
V0.1  
0090508262I  
 

Grindmaster Beverage Dispenser C 2S User Manual
Hasbro Board Games 98048 Asst User Manual
Havis Shields Automobile Accessories KK 100 05 User Manual
Havis Shields Camcorder Accessories KR 800 User Manual
Healthrider Treadmill HCTL06190 User Manual
Heatcraft Refrigeration Products Air Compressor H IM FP User Manual
Hotpoint Clothes Dryer ACC9 BF7 User Manual
Hotpoint Microwave Oven BD52 BD62 User Manual
HP Hewlett Packard All in One Printer 5740 User Manual
Hunter Fan Outdoor Ceiling Fan 42650 02 User Manual