Graco Pet Fence 215963 User Manual

Instructions – Parts List  
Fast-FloR Air Motor  
307456U  
12.5 bar (1.25 MPa, 180 psi) Maximum Air Working Pressure  
Model 215963, Series A  
101.6 mm (4 in.) stroke  
NOTE: To replace Air Motor 215963,  
order Motor Replacement Kit 223099.  
See manual 307977 for parts.  
Important Safety instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
See page 2 for table of contents.  
03652B  
Model 215963 Shown  
 
WARNING  
SKIN INJECTION HAZARD  
Spray from the gun, leaks, or ruptured components can inject fluid into your body and cause extremely  
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also  
cause serious injury.  
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate  
surgical treatment.  
D Do not point the gun at anyone or at any part of the body.  
D Do not put your hand or fingers over the spray tip/nozzle.  
D Do not stop or deflect leaks with your hand, body, glove, or rag.  
D Always have the tip guard and the trigger guard on the gun when spraying.  
D Be sure the gun trigger safety operates before spraying.  
D Close the gun ball valves when you stop spraying.  
D Lock the gun trigger safety when you stop spraying.  
D Follow the Pressure Relief Procedure on page 5 if the spray tip/nozzle clogs and before clean-  
ing, checking, or servicing the equipment.  
D Tighten all fluid connections before operating the equipment.  
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.  
Do not repair high pressure couplings; you must replace the entire hose.  
307456  
3
 
WARNING  
FIRE AND EXPLOSION HAZARD  
Improper grounding, poor ventilation, open flames, or sparks can cause a hazardous condition and  
result in a fire or explosion and serious injury.  
D Ground the equipment and the object being sprayed/dispensed. Refer to Grounding on  
page 5.  
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-  
ing immediately. Do not use the equipment until you identify and correct the problem.  
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid  
being sprayed/dispensed.  
D Keep the spray/dispensing area free of debris, including solvent, rags, and gasoline.  
D Before operating this equipment, extinguish all open flames or pilot lights in the spray/dispensing  
area.  
D Do not smoke in the spray/dispensing area.  
D Do not turn on or off any light switch in the spray/dispensing area while operating or if fumes are  
present.  
D Do not operate a gasoline engine in the spray/dispensing area.  
TOXIC FLUID HAZARD  
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,  
inhaled, or swallowed.  
D Know the specific hazards of the fluid you are using.  
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,  
state, and national guidelines.  
D Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and  
solvent manufacturer.  
4
307456  
 
Installation  
Grounding  
To ground the pump:  
1. UL–Listed Pumps: Use a ground wire, connector,  
Proper grounding is an essential part of maintaining a  
safe system.  
and clamp. See Fig. 1. Loosen screw (X). Insert  
2
one exposed end of a 12 ga (1.5 mm ) minimum  
ground wire (Y) through the eye of the ground  
terminal connector (W) and tighten screw (X)  
securely. Connect the other end of the wire to a  
true earth ground. Order Part No. 237569 Ground  
Wire and Clamp.  
To reduce the risk of static sparking, ground the pump.  
Check your local electrical code for detailed grounding  
instructions for your area and type of equipment. Be  
sure to ground all of this equipment:  
2. Non UL–Listed Pumps: See Fig. 1. Remove the  
ground screw (Z). Fasten the ground connector  
(W) onto the pump with the ground screw (Z) and  
tighten securely. Loosen screw (X). Insert one  
D Pump: Use a ground wire and clamp as shown in  
Fig. 1.  
2
exposed end of a 12 ga (1.5 mm ) minimum  
ground wire (Y) through the eye of the ground  
terminal connector (W) and tighten screw (X)  
securely. Connect the other end of the wire to a  
true earth ground. Order Part No. 222011 Ground  
Connector/Wire and Clamp.  
D Air compressor: Follow manufacturer’s recommen-  
dations.  
D Object being sprayed: Follow your local code.  
W
Z
D All solvent pails used when flushing or relieving  
pressure, always hold a metal part of the gun firmly  
to the side of a grounded metal pail, then trigger the  
gun.  
Y
X
D To maintain grounding continuity when flushing or  
relieving pressure, always hold a metal part of the  
spray gun firmly to the side of a grounded metal  
pail, then trigger the spray gun.  
TI1052  
Fig. 1  
Operation  
1. Shut off the air to the pump.  
Pressure Relief Procedure  
2. Close the bleed-type master air valve (required in  
your system).  
WARNING  
3. Hold a metal part of the gun to the side of a  
grounded metal pail and trigger the gun to relieve  
pressure.  
INJECTION HAZARD  
The system pressure must be manually  
relieved to prevent the system from  
4. Open the fluid drain valve (required in your sys-  
tem), having a container ready to catch the drain-  
age.  
starting or spraying accidentally. Fluid  
under high pressure can be injected through the  
skin and cause serious injury. To reduce the risk of  
an injury from injection, splashing fluid, or moving  
parts, follow the Pressure Relief Procedure  
whenever you:  
5. Leave the drain valve open until you are ready to  
spray/dispense again.  
If you suspect that the spray tip/nozzle or hose is  
clogged or that fluid pressure is not fully relieved after  
following the steps above, very slowly loosen the tip  
guard retaining nut or hose end coupling and relieve  
pressure gradually. Clear the tip or hose obstruction.  
D are instructed to relieve the pressure,  
D stop spraying/dispensing,  
D check or service any of the system equipment,  
D or install or clean the spray tips or nozzles.  
307456  
5
 
Troubleshooting  
Relieve the Pressure before you check or service any  
system equipment.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 5.  
NOTE: Check all other possible problems and solu-  
tions before disassembling the pump.  
Problem  
Solution  
Air motor stalls  
Turn off and relieve air pressure to the motor. Turn on the air  
supply . If the motor does not start, service the air piston (11)  
or springs (5 and 20).  
Air leaks down along the piston shaft (23)  
Air leaks from the piston shaft relief holes (23a)  
Slow operation  
Replace the v-block packing (9).  
Clean and service the piston (11).  
Icing; allow the air motor to thaw.  
Muffler (26) clogged. Clean the muffler with mineral spirits. See  
Cleaning the Muffler on page 7.  
6
307456  
 
Service  
NOTE: Repair Kit 214584 is available. For best results,  
5. A decrease in performance accompanied by a  
slower than normal cycle rate is commonly caused  
by icing. It is recommended that the pump is shut  
down, and the ice is allowed to thaw.  
use all the new parts in the kit, even if the old parts  
look good. Parts included in the kit are marked with a  
dagger, for example (6†), in the text and illustrations.  
6. Reassemble the air piston (11), using new parts as  
needed. Apply a good grade of thread sealant to  
the threads of the screws (12). and torque evenly  
to 1.1–1.6 NSm (10–14 in-lb). With the washer (4)  
in place, apply thread sealant to the threads of the  
piston. Carefully screw the piston (11) onto the  
shaft (23) by hand so it is securely fastened. Do  
not use pliers on the air exhaust plate while tight-  
ening. When installed, there should be 0.8 mm  
(0.032 in.) minimum clearance between the wash-  
er (4) and the piston shaft shoulder. See Fig. 2.  
Air Piston and Lower Spring Service  
WARNING  
To reduce the risk of injury from trapped air pres-  
sure when servicing the air motor, always remove  
air cap (7) from air cylinder (8) before removing air  
cylinder from base (22).  
1. Unscrew the cylinder cap (7) from the cylinder (8).  
To remove the spring (5), pry gently under the coils  
in the direction of the helix.  
Packing Replacement  
1. Unscrew the cylinder cap (7) from the cylinder (8).  
To remove the spring (5), pry gently under the coils  
in the direction of the helix.  
2. Unscrew the cylinder (8) from the base (22) and lift  
the cylinder off the air piston (11). Using a pliers  
(B) on the air exhaust plate (16) and a wrench (C)  
on the piston shaft (23), unscrew the piston from  
the shaft. See Fig. 2.  
2. Unscrew the cylinder (8) from the base (22) and lift  
the cylinder off the air piston (11). Disconnect the  
piston shaft (23) from the pump connecting rod  
and pull the shaft up out of the air motor base.  
Remove and inspect the packing (9†), being  
careful not to mar the inner lip. See Fig. 2.  
CAUTION  
NOTE: Fluoroelastomer packing 111383 is available as  
an accessory, for use with solvents not compatible with  
the standard nitrile rubber packing.  
Ketone fumes may damage the piston o-rings. When  
pumping ketones (such as acetone, MEK, etc.), use  
Conversion Kit 221038. This kit replaces the stan-  
dard fluoroelastomer o-rings with EPDM o-rings  
which are resistant to ketones.  
3. Replace the packing and reassemble the air motor  
in the reverse order of disassembly.  
Upper Spring Replacement  
3. Disassemble the piston and wash all parts in  
compatible solvent. Refer to the parts list on  
page 9. Blow parts dry and inspect for wear or  
damage. If any of the valve plate spacers (13) are  
damaged, replace all three to maintain proper  
clearance between the valve plates and the seats.  
Unscrew the cylinder cap (7) from the cylinder (8). To  
remove the spring (5), pry gently under the coils in the  
direction of the helix.  
Cleaning the Muffler  
To clean the muffler (26), remove it from the unit and  
soak it in mineral spirits, then blow dry with air to  
remove excess solvent.  
4. Remove and inspect the lower spring (20). Re-  
place if necessary, and reinstall.  
307456  
7
 
Service  
220168 Air Valve and  
Piston Assembly (11)  
Motor Cap and Cylinder  
7
*16  
*14  
5
27  
*13  
28  
6†  
15  
*12  
1
8
Piston Rod and Base  
8
23  
20  
Apply Sealant  
1
2
Torque to 1.3–1.6 NSm (10–14 in-lb)  
23a  
Use pliers (B) only when removing  
piston. Do not use when tightening  
piston to rod (23).  
†9  
22  
Piston Detail  
2
B
16*  
4
C
26  
0.8 mm (0.032 in.) Min.  
23  
03654  
Fig. 2  
8
307456  
 
Parts  
7
5
23  
†6  
*16  
9†  
8
*14  
27  
10†  
*13  
28  
22  
6†  
15  
1
3
*12  
1
2
4
Apply Sealant  
1
2
Torque to 1.3–1.6  
NSm (10–14 in-lb)  
2
26  
20  
03655B  
Ref  
No.  
Ref  
No.  
Part No.  
Description  
Qty.  
Part No.  
Description  
Qty.  
1
116343  
SCREW, grounding,  
for non–listed pumps  
LUG, grounding, for UL–listed pumps  
WASHER, tab, for UL–listed pumps  
WASHER, valve  
SPRING, compression  
GASKET, neoprene  
GAP, cylinder  
CYLINDER  
PACKING, v-block; nitrile rubber  
WASHER, backup  
AIR VALVE & PISTON ASSEMBLY  
Includes items 12–16, 27 & 28  
. SCREW, socket hd cap; No. 6–32  
25 mm (1 in.) lg; with copper gasket  
13*  
14*  
15  
16*  
20  
22  
23  
26  
27  
181485  
189210  
181487  
162729  
178780  
215946  
215947  
178490  
108357  
108358  
. SPACER, valve plate  
. PISTON, air, aluminum  
. PLATE, air intake valve  
. PLATE, air exhaust valve  
SPRING, compression  
BASE, air motor (include item 9)  
SHAFT, piston (Includes item 26)  
. MUFFLER  
3
1
1
1
1
1
1
1
1
3
1
2
3
4
5
6†  
7
8
9†  
10†  
11  
104029  
104582  
157872  
178866  
172404  
172406  
172407  
172585  
172595  
220168  
1
1
1
1
2
1
1
1
O-RING; fluoroelastomer  
O-RING; fluoroelastomer  
28  
* Recommended tool box spare parts. Keep these spare  
parts on hand to reduce downtime.  
1
3
12*  
220884  
† Supplied in Repair Kit 214584.  
307456  
9
 
Dimensions  
59 mm (2.32 in.) diameter  
201 mm (7.9 in.)  
1/4–18 npt(f)  
03652B  
Mounting Hole Layout  
32 mm  
(1.26 in.)  
8.50 mm (0.33 in.)  
Diameter  
16 mm  
(0.63 in.)  
27.71 mm  
(1.09 in.)  
10  
307456  
 
Technical Data  
Maximum inbound air pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5 bar (1.25 MPa,180 psi)  
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 npt (f)  
2
Effective piston area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 cm (1.6 sq. in.)  
Effective piston diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35.2 mm (1.4 in.)  
Stroke length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.6 (4 in.)  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 kg (4 lb)  
307456 11  
 
The Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,  
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be  
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-  
stitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of  
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-  
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires  
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers  
to identify the distributor closest to you:  
1–800–328–0211 Toll Free  
612–623–6921  
612–378–3505 Fax  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 307456  
Graco Headquarters: Minneapolis  
International Offices: Belgium, Korea, China, Japan  
GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441  
Copyright 1980, Graco Inc. is registered to ISO 9001  
Revised 04/2009  
12  
307456  
 

Grizzly Drill G0705 User Manual
Haier Washer HBS82 880 User Manual
Harman Kardon Home Theater System SB15 230 User Manual
Harman Stove Company Stove FireLuxe Direct Vent Gas Stove With Top Cooking Burner System User Manual
Hearth and Home Technologies Indoor Fireplace CD4236MILR User Manual
Hearth and Home Technologies Switch WSK 21 User Manual
Heath Zenith Door 598 1227 01 User Manual
Humminbird Fish Finder Wide W User Manual
Husqvarna Tiller 96093000901 User Manual
iHome Switch IH U560SB User Manual