Foundations Baby Furniture 100 EH User Manual

Model 100-EH  
Horizontal Diaper Changing Station  
Installation Instructions  
WARNING  
Failure to follow these warnings and the installation instructions could result in serious injury  
or death.  
Read all instructions before installing diaper changing station. Keep these instructions. DO NOT  
discard.  
SI253D-Gen  
 
WARNING  
A stud MUST be located and used for at least one side of the diaper changing station.  
The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore, MUST be  
firmly secured in order to support the weight they are intended to support. Contact an architect or building contractor  
if any questions.  
INSTALLATION  
1. Locate wood stud where left side of changing station will be mounted to the wall.  
2. Measure up 46” (117 cm) from the floor and mark the wall. This locates the position  
for the top left attachment hole.  
Flat  
Wood Stud  
Washer  
NOTE: Mark on wall MUST be in center of wood stud.  
Finishing  
Washer  
3. Align hole in top left corner of changing station with mark on wall and hold in place.  
4. Using a level and measuring tape, mark the remaining three (3) holes. After marking holes,  
set changing station down on ground.  
Wood  
Screw  
5. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require  
2 people.  
Fig. a  
Changing  
Station  
NOTE 1: For wood studs:  
- If finished wall surface is tile or masonry over wood studs, use  
a 7/32” masonry bit for the pilot hole until you hit the wood  
stud, then change to 1/8” bit.  
- Use wood screws, finishing washers and flat washers (Fig. a).  
Toggle  
Anchor  
Wood Stud  
Flat  
Washer  
NOTE 2: For use with toggle anchors:  
Changing  
Station  
- If finished wall surface has wood studs that are not 16” on center,  
has metal studs, or has an underlying surface of concrete block,  
use 1/2” bit.  
- Use machine screws and flat washers (Fig. b).  
Machine  
Screw  
Fig. b  
- For holes NOT located in a wood stud, toggle anchors MUST be  
used (Fig. c). See “Using Toggle Anchors” section.  
6. Align holes in changing station with drilled holes and secure top left corner of changing  
station to wall stud using the appropriate screw and washer. Continue to secure the  
three (3) remaining corners using the appropriate screws and washers as described  
in Note 1 or Note 2.  
Fig. c  
WARNING  
All 4 of these locations MUST be used for safe installation. The lower holes ensure  
installation through the metal brackets.  
7. Ensure all four (4) screws are tight and snap caps over screw heads.  
Toggle  
Anchor  
Wood Stud  
Using Toggle Anchors:  
1. Insert metal end of toggle anchor into 1/2” hole.  
2. Slide zip strip down snugly against wall.  
3. Snap off break-away pieces of toggle anchor (Fig. d).  
Break-Away  
4. Align holes in changing station with toggle anchors and secure top left corner of changing station to  
wall using machine screws and flat washers. Continue to secure the three (3) remaining corners  
using machine screws and flat washers.  
Fig. d  
5. Ensure all four (4) screws are tight and snap caps over screw heads.  
2
 
RECOMMENDED BLOCKING:  
Top  
If the walls do not have studs on center, then additional blocking  
is necessary (Fig. e).  
Contact an architect or building contractor to make sure the blocking  
is adequate and complies with building codes.  
8 1/4"  
(210 mm)  
For A. D. A.  
Compliance  
46”  
OPERATION:  
(117 cm)  
32"  
Rotate base downward. Place infant on top of the changing surface.  
Use restraint system as described below. After child has been changed,  
remove restraint system and rotate base back up against the wall.  
(813 mm)  
on center  
A. F. F  
Fig. e  
USE OF RESTRAINT SYSTEM:  
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap  
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock  
the strap into place. Slide red locking tab over top of buckle (Fig.f). Reverse steps to loosen strap.  
Locking  
Tab  
Top Of  
Buckle  
MAINTENANCE AND CLEANING:  
Check all hardware and components monthly or as required to ensure hardware is tight and there  
are no missing or damaged components. Take unit out of service if any component is missing or  
damaged and contact customer service to order replacement parts. Do not substitute parts.  
For replacement parts, contact customer service at 1-877-716-2757.  
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong  
chemical cleaners or cleaning agents that may be hazardous to children.  
Fig. f  
WARNING  
Child should never be left unattended.  
Avoid serious injury from falling or sliding out. Always use restraint system.  
Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total  
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to  
exist.  
3
 

Eiki Projector LC SX3 User Manual
Electrolux Freezer 1194 7 GA User Manual
Exmark Lawn Mower 4500 367 User Manual
Fisher Price Bouncy Seat V8606 User Manual
Fostex Portable Speaker FE166e User Manual
Gamages Furnace 58DHB User Manual
Gateway Cable Box CG3000 User Manual
GE Answering Machine 27851FE1 User Manual
Gianni Industries Power Supply PSM 01T 4 User Manual
Goodman Mfg Air Conditioner Air Conditioning and Heat Pump Packaged Units User Manual