Cannon Fishing Equipment 1904030 User Manual

PEDESTAL MOUNTS  
4” Fixed Pedestal mount 1904030  
6” Fixed Pedestal mount 1904031  
4” Swivel Pedestal mount 1904032  
6” Swivel Pedestal mount 1904033  
CAUTION:  
READ THIS MANUAL CAREFULLY  
BEFORE OPERATING YOUR  
NEW CANNON ACCESSORY.  
RETAIN FOR FUTURE REFERENCE.  
NOTE: Do not return your CANNON accessory to your  
retailer. Your retailer is not authorized to repair or re-  
place this unit. You may obtain service by:  
calling CANNON at 1-800-227-6433;  
returning your accessory to the Factory Service Center;  
121 Power Drive, Mankato, MN 56001  
Please include proof of purchase and purchase date for  
warranty service with any of the above options.  
Owner’s Manual  
 
How to use the Swivel Pedestal  
Cannon’s swivel base downrigger pedestals allow you to rotate the mounting plate for optimal positioning.  
To rotate the mounting plate, disengage the lock pin by pulling the lock pin handle down. Turn the plate to the de-  
sired angle and release the spring loaded lock pin making sure that it reengages. Check to make sure the swivel is  
in a fixed position.  
Swivel Base Break Away Reset  
The Cannon Swivel bases feature a unique break away system which allows the top plate to rotate while in  
the locked position. The break away feature will help prevent damage to the downrigger and boat in the event that  
the downrigger boom or ball would strike an object. If this should occur, the mounting plate of the swivel pedestal  
will turn, giving way to the unexpected load. The mounting plate can be reset back to any position by following  
these steps:  
1) Locate the 3/8” bolts on the bottom of the top plate (See Figure 1).  
2) With the pedestal locked in any position, loosen the bolts  
3) Rotate the mounting plate back to the desired position.  
4) Tighten the 3/8” bolts to 25 ft-lb.  
Note: The downrigger weight must be stowed before resetting the swivel pedestal mount.  
3/8” Tension Bolts  
25 ft-lb torque  
35 ft-lb torque max  
Lock Pin Handle  
Figure 1  
3
 
Mounting the Pedestal to Your Boat  
Mounting Directly to Deck or Gunnel  
Carefully choose an ideal position where you may best utilize your pedestal mount. Use the base of the  
pedestal as a template to mark hole locations and drill four 9/32" diameter through holes. Fix the pedestal to the  
deck or gunnel using four 1/4”-20 flat head screws with four flat washers, lock washers, and nuts (not included). To  
determine the length of screw needed, measure the thickness of deck that you are mounting to and add at least  
3/4”.  
Mounting to Cannon Track Mount  
For versatility and lightening quick mounting, the Cannon Mounting  
Track system is ideal for utilizing your pedestal mount on your boat. Slide the  
base of the pedestal into the track and tighten the thumb screws to fix the pedes-  
tal in position. You may use a 3/16” Allen wrench for additional tightening.  
CAUTION:  
The Cannon Pedestal  
Mount is intended for use  
with a Track that is  
mounted directly to the  
deck of the boat ONLY.  
Note: For the Swivel Pedestal Mount, rotate the release handle to access the top of  
the thumb screw with the Allen wrench.  
1904025 Aluminum Mounting Track 6”  
1904026 Aluminum Mounting Track 12”  
1904027 Aluminum Mounting Track 18”  
1904028 Aluminum Mounting Track 24”  
1904029 Aluminum Mounting Track 36”  
Cannon tracks allow for flexible mounting positions and easy  
removal of Cannon’s track system accessories. Locking grooves allow  
thumb screws to index with track and prevent accessories from twisting.  
The system is compatible with Cannon, Bert’s, and Traxtech track system  
products. Components are made from clear anodized aluminum and  
stainless steel for strength and corrosion resistance. All mounting hard-  
ware included. Available in 6, 12, 18, 24, and 36 inch lengths.  
Mounting to Cannon Deck Mount  
The Cannon Deck Mount works great for adding stability and easy removal of your pedestal mount. With  
your Cannon Deck Mount installed on your boat, attach your pedestal mount by removing the thumb screws and  
fastening the pedestal base to the plate with four 1/4”-20 x 3/8” long flat head screws.  
1904000 Deck Mount  
The Cannon Deck Mount plate is a four inch by three inch  
clear anodized aluminum plate which allows the hard mounting of  
Cannon Dual Axis Rod Holders. The plate comes with a black pro-  
tective mounting boot and all mounting hardware.  
4
 
Mounting Your Downrigger to the Pedestal Mount  
The Cannon Pedestal Mount provides 1/4”-20 tapped mounting holes for attaching most downrigger  
mounting bases. To attach a mounting base you will need four 1/4”-20 screws (not included). To determine the  
length of screws needed, measure the thickness of the downrigger mounting base and add 1/2”. See below for  
screw lengths for the Cannon Downrigger mounting bases.  
Magnum / Digi-Troll Tall Mounting Base —  
Uni-Troll Low-profile Mounting Base —  
Easi-Troll / Lake-Troll Tab-Lock Base —  
2” Long Truss Head screw  
1” Long Truss Head screw  
3/4” Long Truss Head screw  
Pedestal Mount \ Accessory Compatibility  
Mounts  
Track Mount  
Gimbal Track Mount Pedestal Track Mount  
Rail Mount  
Clamp Mount  
Deck Mount  
Pedestal  
4" Fixed Mount  
6" Fixed Mount  
4" Swivel Mount  
6" Swivel Mount  
- Compatible  
- Not Compatible  
Troubleshooting - Swivel Pedestal  
Problem: Pedestal will not rotate when the lock pin is disengaged.  
Make sure the downrigger line is all the way up. Any load on the downrigger or pedestal may prevent the pin from  
disengaging. Spray a lubricant into the slot which the lock pin slides. Make sure lock pin moves freely up / down.  
Problem: Pedestal rotates while in locked position under normal use.  
The break away bolts are not tight enough. Re-torque bolts to 25 ft-lb.  
NOTE: Bolts may have to be tightened higher than 25 ft. lbs under some conditions. Do not exceed 35 ft-lb as this may  
damage the top plate.  
Problem: Pedestal did not breakaway while locked when the boom struck an object.  
The break away bolts are over-tightened. Loosen bolts and re-torque to 25 ft. lbs.  
Replacement Parts  
Part  
Part Number Description  
USED ON  
3393413  
THUMB SCREW  
1904030, 1904031, 1904032, 1904033  
5
 
CANNON® LIMITED WARRANTY  
Johnson Outdoors Inc. warrants to the original purchaser that the accompanying product (see exclusions below) is free from  
defects in material or workmanship for a period of one (1) year from the date of purchase. Within the warranty period, Johnson  
Outdoors Inc. will, at its option, either repair or replace same without charge (but no cash refunds will be made). The unit must be  
returned, prepaid and with proof of the date of purchase to the following:  
Johnson Outdoors, Inc Cannon Division, 121 Power Drive, Mankato, MN 56001  
This limited warranty may be enforced only by the original purchaser; all subsequent purchasers acquire the product "as is" with-  
out any benefit of this limited warranty. Repair or replacement of the product as set forth in this limited warranty shall be the origi-  
nal purchaser’s sole and exclusive remedy and Johnson Outdoors Inc.’s sole and exclusive liability for breach of this warranty.  
EXCLUSIONS  
This warranty does not apply in the following circumstances:  
When the product has been connected, installed, combined, altered, adjusted, serviced, repaired, or handled in a manner other than according  
to the instructions furnished with the product  
When a serial number has been defaced, altered, or removed  
When any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, carelessness, or abnormal use, or from any  
failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner's manual  
LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND CERTAIN DAMAGES  
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THESE LIMITED WARRANTIES. JOHNSON OUTDOORS INC.  
DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED WAR-  
RANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EX-  
TEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE. THIS WRITING CONSTITUTES THE ENTIRE AGREEMENT  
OF THE PARTIES WITH RESPECT TO THE SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT SHALL BE VALID  
UNLESS IN WRITING SIGNED BY JOHNSON OUTDOORS INC.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of consequential damages, so the above limitation or exclusion  
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.  
Johnson Outdoors, Inc. / Cannon Division  
121 Power Drive, Mankato, MN 56001  
1-800-227-6433  
© 2008 Johnson Outdoors, Inc. All rights reserved.  
To download product manuals or purchase Cannon products from an authorized dealer, please visit our web page at www.cannondownriggers.com  
WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.  
Form No. 3397127 Rev D  
6
 

BenQ Computer Monitor GW2255 User Manual
Black Decker Impact Driver FS1202ID User Manual
Boston Acoustics Speaker G510RS User Manual
Braun Coffee Grinder KF 520 User Manual
Brother Printer QL 500W User Manual
Califone DJ Equipment PA419 User Manual
Campbell Hausfeld Sander DG480000CK User Manual
Carrier Thermostat 33CSIRRCVR 01 User Manual
Casio Cash Register PCR T465 User Manual
Chariot Carriers Baby Carrier Babya Carrier User Manual